Dies-and-Presses

Lee 204 Ruger Full Length Size Die

Lee 204 Ruger Full Length Size Die

Lee 25/06 Rem Full Length Size Die

Lee 25/06 Rem Full Length Size Die

Lee 338 Lapua Full Length Size Die

Lee 338 Lapua Full Length Size Die

Lee 7mm 08 Seating Die Only

Lee 7mm 08 Seating Die Only

Lee 223 Factory Crimp Die crimps the bullet in place more firmly than any other tool. Works with 223 Remington and 223 Ackley Improved. Tests demonstrate that even bullets which have no crimp groove will shoot more accurately. A firm crimp improves accuracy because pressure must build to a higher level before the bullet begins to move. This higher start pressure insures a more uniform pressure curve and less velocity variation.

Lee 22 Hornet Pacesetter 3 Die Set

Lee 6.5X55 Mauser Collet Die Set includes a Collet Die that uses a collet to squeeze a mandrel creating a precisely aligned case neck while reducing run out, Dead Length Bullet Seater Die, Shell Holder, Powder Dipper and Load Data

Lee 300 WM Pacesetter 3-Die Set includes Full Length Sizing Die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data

Lee 22/250 Really Great Buy. Includes Full Length Sizer Die and Easy Adjust Dead Length Bullet Seating Die (no crimp).

Lee 270 Winchester Collet Die Set includes a Collet Die that uses a collet to squeeze a mandrel creating a precisely aligned case neck while reducing run out, Dead Length Bullet Seater Die, Shell Holder, Powder Dipper and Load Data

• Loads 12 Gauge 2-3/4", 3" Shells
• Comes with 6 and 8 point crimp starters
• Safety charge bar

Lee 38 Special Pistol 3-Die Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. Note: you may use the 38 Special die set to reload for the 357 Mag. You would have to back out the Powder Thru Expander Die, and the Bullet Seating and Crimping Die about 2 turns to compensate for the longer 357 case.

Lee 243 Win Full Length Size Die

Lee 243 Win Full Length Size Die

Lee 223 Rem Full Length Size Die

Lee 223 Rem Full Length Size Die

Lee 9MM Luger Pistol 3-Die Set includes Carbide Full Length Sizing Die, Bullet Seating Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data

Lee 44 SPL Pistol 4-Die Set. Includes Carbide Full Length Die, Bullet Seating Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and Instructions/Load Data. Note: These dies can be used to reload 44 Magnum and 445 Super Mag

Keep your scales free from any unwanted dust or grime when filling cartridges.

Keep your scales free from any unwanted dust or grime when filling cartridges.

The Dust Cover fits 5-0-2, 5-0-5, and 5-10 model scales.

RCBS announces the introduction of the Rock Chucker Supreme Auto Priming Unit. This conversion will allow the users of the current single-stage model to advance to a tube-fed auto-priming system, eliminating the need to handle primers and boasting a 100-primer capacity. Press not included

RCBS announces the introduction of the Rock Chucker Supreme Auto Priming Unit. This conversion will allow the users of the current single-stage model to advance to a tube-fed auto-priming system, eliminating the need to handle primers and boasting a 100-primer capacity. Press not included

These steel constructed locking rings allow the reloader to set up dies and lock them in place so they can be removed and replaced without having to recalibrate. Fits on standard 7/8"-14 threaded dies.

These steel constructed locking rings allow the reloader to set up dies and lock them in place so they can be removed and replaced without having to recalibrate. Fits on standard 7/8"-14 threaded dies.

Elastomer wiper and teflon coated metal casting make this the smoothest operating measure. Will not cut powder and almost totally eliminates leakage. Large hopper with shut-off valve is attached with brass thumb nuts for the ultimate in disk changing convenience. Increased safety with positive pull-back lever. Includes swivel adapter and spring return lever with spring and all four disks. Many prefer the Pro Auto-Disk for mass production reloading. The hopper holds 1/2 pound of powder.

Lee Pro Auto Disk is designed for use with Pro 1000 and Load-Master presses. Used with the Powder Thru Expanding Die or Rifle Charging Die. Includes swivel adapter and spring return lever with spring.

Includes 4 disks to adjust your charges with:

• Disk A = .30 to .43 cc
• Disk B = .46 to .66 cc
• Disk C = .71 to 1.02 cc
• Disk D = 1.09 to 1.57 cc

Lee 338 Lapua Collet Die Only 1.25-12 Thread

Lee 338 Lapua Collet Die Only 1.25-12 Thread

Lee Short and Long Charging Dies are included in this kit for use with the Auto-Disk, Pro Auto-Disk and Auto-Drum Powder Measure. Works with cases .860 to 2.620 inches long, and bullet diameters .223 and larger.

Works the same as the pistol Powder Through Expanding Die, except it does not expand the case mouth. Rifle case expansion is done in the Sizing die

• RCBS Neck Sizer Only.
• .223 Rem.

• Includes Breech Lock Hand Press, Ram Prime, Powder Funnel, Case Lube and one Breech Lock Quick Change Bushing
• Maximum overall length this reloading press can accept is 3.650 inches
• Order a set of dies to complete